WEP Encryption in Use
A wireless network is protected with Wired Equivalent Privacy (WEP), whose key can be recovered from captured traffic within minutes using freely available tools.
| Severity | High |
| CVSS 3.1 | 8.1 CVSS:3.1/AV:A/AC:L/PR:N/UI:N/S:U/C:H/I:H/A:N Open in the calculator |
| CVSS 4.0 | 8.6 CVSS:4.0/AV:A/AC:L/AT:N/PR:N/UI:N/VC:H/VI:H/VA:N/SC:N/SI:N/SA:N Open in the calculator |
| CWE | CWE-327: Use of a Broken or Risky Cryptographic Algorithm |
| OWASP Top 10 | A04:2025 Cryptographic Failures |
| MITRE ATT&CK | T1669 Wi-Fi Networks, T1040 Network Sniffing |
| Category | Cryptographic Failures |
Description
One or more wireless networks use Wired Equivalent Privacy (WEP) to encrypt traffic. WEP combines a shared key with a 24-bit initialisation vector (IV) and encrypts each frame with the RC4 stream cipher. The IV space is small, IVs are sent in cleartext and repeat quickly, and some IV values leak information about the key, so an attacker who collects enough frames can calculate the key itself. WEP's integrity check is a CRC-32 checksum rather than a cryptographic one, so frames can also be altered or forged without detection.
Statistical attacks such as PTW, implemented in tools including aircrack-ng, recover a 104-bit key from tens of thousands of captured frames. Where the network is quiet, an attacker can replay captured frames, such as ARP requests, to make the access point generate the traffic needed, so recovery normally takes minutes. Key length makes no practical difference, and the shared-key authentication option exposes keystream rather than adding protection.
The attacker needs no credentials, only a position within radio range, which can be outside the building where the signal reaches. With the key, they can decrypt all traffic on the network, both live and previously captured, and join it as a legitimate client, from where they can reach every system the wireless network can reach, intercept and alter unprotected traffic, and attack connected devices. Because the key is shared, it stays exposed until it is changed on every device.
WEP is identified from beacon frames during a wireless survey: tools such as airodump-ng and Kismet report the network's encryption as WEP. It is most often found on networks kept for legacy devices, such as older handheld scanners, printers, or industrial and medical equipment that cannot use anything stronger.
Remediation
WEP cannot be configured securely and should be removed:
- Reconfigure the network to use WPA3, either WPA3-Personal (SAE) or WPA3-Enterprise, as certified by the Wi-Fi Alliance. Where some clients do not yet support WPA3, use WPA2 with AES-CCMP only, or WPA2/WPA3 transition mode, with TKIP disabled.
- Replace or upgrade devices that only support WEP, checking first for vendor firmware that adds WPA2 or WPA3 support.
- Where a legacy device cannot be replaced immediately, move it to a dedicated SSID and VLAN, allow only the specific traffic it needs through a firewall, and monitor that segment until the device is retired.
- Once WEP is removed, treat the old key as compromised, and change any credentials that crossed the network without another layer of encryption.
Confirm the fix with a wireless survey showing that no SSID advertises WEP, and by checking that any remaining legacy segment cannot reach other internal networks.
References
Add This Finding to Your Library
In Pental this write-up is in Settings, Library. Add to my library copies it into your own, rated in your firm's CVSS version, ready to put in your own words.
Free trialYour trial starts when your portal goes live, not when you sign up, so the time you spend setting up does not count. · No card required
Only need the reporting? Our reporting tool is free and open source, with the same library.